面向一体化计算的整体式液体冲压发动机建模及性能评估

为发展冲压发动机性能工程预估方法,建立了面向一体化计算的整体式液体冲压发动机性能计算模型,并使其兼容基团贡献算法,提高了拓展性。利用模型分析了冲压发动机在攻角0°～6°、高度0～18km、马赫数2.0～3.5、余气系数1.0～2.9范围工况多维度连续变化下,比冲、推力系数和燃油质量流量的速度-高度特性、高度-节流特性、节流-速度特性以及攻角特性。研究结果表明:性能计算模型可在一体化计算条件下、基团贡献算法允许范围内,不依赖试验数据对冲压发动机性能预估,计算结果与技术参考值相比相对误差均小于14%。推力系数和比冲具有基本一致的速度-高度特性和相似的高度-节流特性,受燃气组分影响,推力系数和比冲的节流-速度特性差异明显。燃油质量流量的变化规律不同于比冲和推力系数,在进入平流层后呈现折缓趋势,而呈现连续性,速度越大、高度越低、余气系数越小,燃油质量流量越高,反之则越小。引入攻角以后,攻角越大,比冲和推力系数越低,进气道起动马赫数越高;攻角-起动马赫数曲线小范围内近似线性,攻角超过5.6°非线性加剧。     

基于综合模糊聚类算法的液体火箭发动机故障诊断

基于液体火箭发动机正常及故障状况数据的完备程度和数据质量的不断提高,提出一种基于数据驱动的综合模糊聚类算法用于故障诊断。采用模糊c均值(FCM)算法对已知正常样本数据进行聚类得到最优的聚类中心,将所得到的聚类中心作为先验样本数据用于传递闭包法最优分类结果的选择从而得到故障检测结果,该算法只需要少量的正常先验样本数据就能快速、准确的检测出故障;随后采用FCM算法进行故障分类,可以根据现有的故障数据库进行聚类得到对应的故障类型,并且可以给出故障幅值范围。模型仿真结果表明:该算法对故障的检测率可达968%,故障隔离率达到94%。某型液体火箭发动机实际试车数据结果表明:该故障诊断算法能够准确及时的检测并隔离出故障。     

高温高速气流总焓接触测试法对比分析

发动机尾焰、燃烧加热、电弧加热器等高温高速气流总焓测量存在较大误差,采用结构优化的质量吸入水冷焓探针,标定后的驻点热流和驻点压力探针(Fay-Riddell公式法)对高温高速气流总焓进行了对比测试。结果表明:焓值为2.5~5 MJ/kg时,焓探针的测试误差约为3.38%,采用Fay-Riddell公式法获得焓值的误差约为3%。焓探针与Fay-Riddell公式法平均偏差约为4.65%。在地面模拟试验时采用两种测焓方法确定测试精度,对减小高温高速气流测焓误差,提高试验模拟精度具有积极的作用。     

航空发动机适航审定喘振与失速影响因素

将气动热力基础理论与适航领域工程问题有机结合,对典型的喘振和失速影响因素开展了系统的研究,发展了一套多影响因素作用下航空发动机稳定裕度快速预估方法;在此基础上以JT9D发动机为研究对象,开展了喘振和失速主要影响因素的影响规律研究,结果显示对风扇部件稳定裕度影响权重最大的是进气畸变,对增压级和高压压气机影响权重最大的是寿命期内结构衰变。研究结果进一步明确了喘振和失速适航条款符合性验证活动的关键要素,完善了条款适航符合性验证流程,为进一步提升我国民用发动机适航审定能力提供了技术支撑。     

空间电动力绳系电流峰值点变化规律研究

为研究电流峰值点在几种影响因素下的变化规律,建立一种能够捕捉绳系电子发射与收集自洽平衡过程的新算法——电路空间耦合算法。为验证该方法的计算精度,以1.35kW霍尔推力器为等离子体源,在真空舱内开展绳系的电荷收集试验,在电路参数方面,计算精度约为12.8%,在场参数方面,计算精度约为3.6%。在此基础上,针对不同偏置电压、绳系长度以及绳系直径,对绳系的绳上电流分布、电势分布以及空间电势分布等参数进行数值计算。结果显示:电动力绳系的电流峰值点会随着偏置电压升高、绳系长度增加及绳系直径增大而发生比例上的向阳极端漂移,揭示了电子轨道运动限制的机制在各类壁面电荷输运机制中占优,导致电流峰值点漂移的产生。     

Advances in critical technologies for hypersonic and high-enthalpy wind tunnel

Hypersonic and high-enthalpy wind tunnels and their measurement techniques are the cornerstone of the hypersonic flight era that is a dream for human beings to fly faster, higher and further. The great progress has been achieved during the recent years and their critical technologies are still in an urgent need for further development. There are at least four kinds of hypersonic and high-enthalpy wind tunnels that are widely applied over the world and can be classified according to their operation modes. These wind tunnels are named as air-directly-heated hypersonic wind tunnel, light-gas-heated shock tunnel, free-piston-driven shock tunnel and detonation-driven shock tunnel, respectively. The critical technologies for developing the wind tunnels are introduced in this paper, and their merits and weakness are discussed based on wind tunnel performance evaluation. Measurement techniques especially developed for high-enthalpy flows are a part of the hypersonic wind tunnel technology because the flow is a chemically reacting gas motion and its diagnosis needs specially designed instruments. Three kinds of the measurement techniques considered to be of primary importance are introduced here, including the heat flux sensor, the aerodynamic balance, and optical diagnosis techniques. The techniques are developed usually for conventional wind tunnels, but further improved for hypersonic and high-enthalpy tunnels. The hypersonic ground test facilities have provided us with most of valuable experimental data on high-enthalpy flows and will play a more important role in hypersonic research area in the future. Therefore, several prospects for developing hypersonic and high-enthalpy wind tunnels are presented from our point of view.     

Optimization and verification of free flight separation similarity law in high-speed wind tunnel

Based on the similarity of separation time, a similarity law optimization method for high-speed weapon delivery test is derived. The typical separation state under wind load is simulated by the numerical method. The real separation data of aircraft, separation data of previous test methods, separation data of ideal wind tunnel test of previous methods, and simulation data of the proposed optimization method are obtained. A comparison of the data shows that the method proposed can improve the performance of tracking. Similarity law optimization starts with the development of motion equations and dynamic equations in the windless state to address the problems of mismatching between vertical and horizontal displacement, and to address the problems of separation trajectory distortion caused by insufficient gravity acceleration of the scaling model of existing light model. The ejection velocity of the model is taken as a factor/vector, and is adjusted reasonably to compensate the linear displacement insufficiency caused by the insufficient vertical acceleration of the light model method, so as to ensure the matching of the vertical and horizontal displacement of the projectile, and to improve the consistency between the test results of high-speed projection and the actual separation trajectory. The optimized similarity law is applicable to many existing free-throwing modes of high-speed wind tunnels. The optimized similarity law is not affected by the ejection velocity and hanging mode of the projectile. The optimized similarity law is suitable not only for the launching of the buried ammunition compartment and external stores, but also for the test design of projectile launching and gravity separation.     

高湍流度时全气膜涡轮叶片表面冷却和换热特性的实验研究

为获得高主流湍流度时全气膜涡轮叶片表面的冷却和换热特性,在跨声速风洞中实验研究了质量流量比(MFR)和主流雷诺数(Re)对叶片表面气膜冷却效率和换热系数比的影响。在叶片前缘布置了5排圆形孔,在吸力面和压力面分别布置了3排和6排圆形孔,实验结果由嵌入在叶片中截面的热电偶测得。实验中基于弦长的主流雷诺数的范围为3.0×105～9.0×105,叶栅出口马赫数Ma为0.8, MFR的范围是5.5%～12.5%,主流湍流度Tu为14.7%。实验结果表明:主流雷诺数升高显著增强了叶片表面的换热,使层流边界层到湍流边界层的转捩位置提前。对于吸力面S/C0.2的区域(S/C为当地弧长与弦长之比),气膜冷却效率受MFR影响明显,当MFR大于7.7%时提高MFR会导致气膜冷却效率降低;该区域的换热系数比在中低雷诺数时受MFR影响较小,在高雷诺数时随MFR升高而升高。压力面S/C-0.7区域的气膜冷却效率随MFR升高而升高,-0.7S/C-0.4区域的气膜冷却效率受MFR影响较小,对于整个压力面而言,MFR升高提高了叶片表面的换热系数。相对于叶片其它区域,压力面后半段区域和吸力面的气膜冷却效率受雷诺数影响较大。     

用于光波纳米推力器的颗粒供应技术和光聚积技术研究

为提高光波纳米推力器在轨应用的可行性,针对与其匹配的颗粒供应技术和光聚积技术进行研究。提出整个推进系统的设计思路,通过建立理论计算和数值计算模型,分析颗粒供应技术和光聚积技术的各项核心结构参数的设计方法。计算结果表明:颗粒供应装置的正负电极内径之比(W/D)会影响正负电荷产生的总量之比,在W/D=300/322附近时,正负电荷比例接近1:1。静电诱导电压为9 V,当中和通道长度大于37.5mm时,正负颗粒可以视为完全中和。光聚积设计思路可令聚积球对光能的利用率在32.8%左右。两种相关技术的装置与推力器在结构上能够对接、在性能上可以匹配,从理论上表明了两种支撑技术的可行性。     

空心气冷低压涡轮动叶气热耦合数值模拟

以空心气冷低压涡轮动叶为研究对象,采用高质量的流体域和固体域网格控制技术,带转捩模型的双方程SST湍流模型,开展了基于CFD方法的叶片气热耦合问题研究。获得了不同冷气流量比(分别为1.0%,1.38%,1.8%和2.2%)、温比(分别为2.1,2.25,2.3,2.4和2.5)和压比(分别为1.4,1.6和1.8)对叶片换热特性的影响规律,设计状态中截面按弧长平均的叶片壁面金属温度计算值较试验值偏小0.3%,气热耦合计算的叶片壁面温度分布与试验结果吻合良好,验证了气热强耦合计算方法的精度,为涡轮叶片温度场分析提供了一种有效的方法。